Elevator Supplier Share Sightseeing Elevator Installation Requirements
The sightseeing elevator can be installed inside or outside the new building, or it can be implemented as an engineering project for the renovation of existing buildings. It is worth noting that the sightseeing elevator installed outside the building must meet special conditions to withstand the adverse effects of meteorological conditions at the installation site on the elevator equipment. The following fuji Elevator Supplier will talk about relevant knowledge.
Icing and frost pose a great threat to the operation of the general-purpose outdoor sightseeing ladder. Industry insiders suggest that outdoor sightseeing elevators are not suitable for places where icing and frost occur frequently. In places where icing and frost do not occur frequently, outdoor icy ladders should be discontinued in the event of ice and frost. Gale weather may be the second reason people have to reduce the speed of outdoor sightseeing ladders or stop elevators. Places, where the wind is often blown, are not suitable for installing outdoor sightseeing ladders unless the elevator shaft is located completely outside the building. Therefore, in this case, it is very important to install an indoor elevator in the building so that the indoor elevator can still ensure that the vertical transportation is not interrupted when the weather conditions are not conducive to the operation of the outdoor elevator.
Moderate rainfall and hot weather do not pose a hazard to well-designed, well-installed outdoor ladders, but the natural causes of seasonal dust and sand-sanding weather may cause suitable equipment to wear and tear and increase maintenance costs, which is also in determining the building. One of the issues that must be considered before installing an outdoor elevator. All elevator parts exposed to the open air should be properly treated and protected.
The sightseeing elevator can be driven by a traction drive or a hydraulic drive, the choice of which depends to a large extent on the lift height of the elevator and the hoistway conditions of the building. Since the sightseeing elevator has high requirements on the running quality, variable frequency speed regulation or hydraulic driving is usually adopted. Sightseeing elevators generally do not require high operating speeds, as passengers generally wish to stay in the car for a while to view the scenery outside the car. The speed of the sightseeing elevator is suitable for speeds lower than that of similar objects, as long as the vertical traffic in the building is not affected because the speed is too slow.
The car area of the sightseeing elevator consists of two parts, the passenger area, and the viewing area. The passenger area is adjacent to the elevator car door, which is usually located at the rear of the car. It is worth noting that the ratio of the area of the viewing area to the passenger area must be appropriate. The area ratio will increase the difficulty of the car balance, and the passengers enter the car due to the limited width of the car in the passenger area.
The novelty of a sightseeing elevator is the use of a transparent viewing wall in the car viewing area. All personnel involved in the design, manufacture, and installation of sightseeing elevators must be in the glass assembly industry. Before designing a sightseeing elevator car, designers should consult the relevant building codes to understand the specifications for the use of glass materials in elevator cars and shafts. Transparent viewing walls shall not be used as load-bearing or structural components during the design and installation process. The frame around the transparent viewing wall should be sufficient to withstand all levels of force, including the forces that elevator passengers may generate, without distortion that affects safety performance.
The car top and the car floor cover must be strong and strong, but they must be lightweight and easy to replace. It should be designed so that the exterior surface of the car is not damaged by repair work, oil stains or excessive lubricant.
The exposed surface of the elevator hall door and its accessories and the visible portions of the exterior of the car should have a smooth, durable, corrosion-resistant and easy-to-clean surface. The surface of the material is generally made of corrosion-resistant steel or enamel.
It is possible to provide maintenance personnel with safe car top operation and driving conditions so that they can perform daily equipment maintenance and inspection on the car roof. Daily equipment maintenance includes cleaning of all publicly visible parts and components in the hoistway, such as hall doors and door frame attachments. The car of the sightseeing elevator usually does not have a car top emergency exit. The pit and the bottom layer are protected at the lowest level of the elevator. The space below the hoistway should be isolated so that maintenance personnel can safely access the parts outside th
37 total views, 1 today
You must be logged in to inquire about this ad.
Information about the ad poster
- Listed by:fujiBlanche
- Member Since: November 22, 2018
Other items listed by fujiBlanche
- Elevator Supplier Share The Time Of The Ladder
- Elevator Factory Sharing Elevators Are Not Sealed
- Elevator Manufacturers Share How To Design The Size Of The Elevator
- Elevator Factory Reminds You To Pay Attention To The Maintenance Of The Villa Elevator
- Elevator Manufacturer Don’T Think That The “Abnormality” Of The Elevator Is Bad Performance
Popular Ads Overall
- Pride of Abia Shoes (847 views)
- Crayfish (630 views)
- super fast batter charger (600 views)
- SANTAL PLANTAIN FLOUR (556 views)
- Pride of Abia Shoes (456 views)
- Ankara bags (436 views)
- Pride of Abia Shoes (426 views)
- Brogues (395 views)
- SUPER FAST CHARGING UPS/inverter WITH BATTERY MANAGEMENT TECHNOLOGY (391 views)
- High quality Plastic PVC Sheet (375 views)